Possible cause of failure:
Interior of spindle contaminated with coolant. Grease was washed out of #1 & #2 front bearings, #3 nearly so.
#5 rear bearing also heavily contaminated & beginning to lock up.
Front bearing capture is set with .070” of shims behind front cover.
Front housing 150mm ID is oversized +10/+15µ (ISO is +/-9µ)
Rear housing 140mm ID has wear & dents and is oversized & egged +25/+35µ (ISO is 0/+10µ)
Clean, inspect overall dimensions.
Grind, chrome plate & finish grind front & rear housings.
Replace bearings, Inpro seal, o-rings & assembly screws.
Adjust preload, balance, assemble and break in. Final quality control inspection.
Does your spindle need repair? GET A QUOTE TODAY
Spindle came in with contaminated front bearings. We kiss ground the taper, face and the front bearing shoulder. We then assembled the spindle with a new inproseal, test ran and balanced. If th [...]
8000 rpm This spindle needed a kiss grind to the taper, drawbar rebuild and bearing replacement. [...]
Hardinge Conquest SG-2, grease lubrication, belt driven, 6,000 rpm A long time MTR (machine tool rebuilder) had his own spindle in need of rebuild. He… [...]
5,000 rpm The bearings in this spindle reached the end of their lifespan. The ID collet taper had 10 microns of run out. We were able to kiss grind the ID taper and after assembly it had less t [...]
Possible cause of failure: Front & rear bearings, rear housing and stator contaminated with coolant. All dimensions are within ISO tolerance. Recommended action: Clean, inspect overall dimen [...]
I really didn’t expect this; You guys really pulled it off! My many thanks to Sandy, Louis and your outstanding crew for helping us get back into production.
Lou all in all everything is running good. Just had a call from Sandy just the other day, its funny great minds think alike. Its great not to be sending spindles out on a regular basis since you addressed my problems, but I know they will still be coming sooner or later. Never a problem when we get them back , run better than new. Hope everything is ok there. Please tell everyone there that we here appreciate everything that you do to keep us up and running and the quick turnarounds. Have delt with the rest now deal with the best. Have a great week end and up and coming holiday.
Thank you Debbie just received spindle today and WOW ! what a nice job. Can’t wait to use it. Thank the Northland team for us for a job well done
Both of the spindles that you repaired are on the machines and running great. We don’t have any spares for those grinders. We probably will not be purchasing a spare, as you have been able to turn around the repairs quickly and the price of a spare is cost prohibitive.
I am writing to thank Northland Tool for going the extra mile and saving my company from expensive machine downtime and expensive repairs. We have always sent our Chiron spindles for repair as a shaft with bearings. None of our previous rebuilders pointed out the bearing fretting or the fact that the housing in the machine was out of tolerance and causing premature failure to the spindles. After Northland fixed the housings the spindles have never sounded as good or run as well! Great job guys!
The detailed cause of failure reports and the expert technical advice that Northland Tool provides is bar none the best I have ever seen. We struggled to keep two of our large our milling spindles running for longer than 6 to 12 months. Northland Tools evaluation showed that the hydraulic nuts were not holding the assembly together causing premature spindle failure. We discussed this in detail and mutually decided to modify the spindle shaft to prevent this from occurring again. The first spindle we performed this on is still in the machine running like new after 3 years. That’s over three times the life of previous repairs and it’s still going strong. Easily over $40,000.00 of savings so far on that one machine and counting.
Your people go above and beyond the call of duty when it comes to spindle repair. When we had difficulty with the spindle installation and we were able to talk directly to a spindle technician that helped us troubleshoot the issue it helped us out of a bind. We have sent several spindles to you and have nothing but great things to say.
Thank you for your attention with my quick turn spindle repair. Your status updates allowed me to plan around machine downtime and I now know that you deliver on your promises. In the past other spindle repair vendors talked a big game and consistently failed to deliver. You not only delivered my spindle before the due date but you kept me informed throughout the entire repair process.
You performed a miracle with my BIG PLUS spindle. After crashing the spindle severely damaging the taper we found that a replacement spindle was not only cost prohibitive but had a long delivery. Your repair was a fraction of the cost of new and you never would know that the spindle was damaged to the extent it was.
Catastrophic bearing failure was the main cause of this spindle malfunction
Continue reading to learn how Northland Tool performed this repair and converted a Weiss GHK 176239 spindle from grease-injected to permanent grease lubrication…