Daewoo DMV-3016, 8,000 RPM stator drive, oil mist lubrication, CAT40 taper
The bearings in this vertical machining center spindle were very noisy when it arrived at our shop for evaluation & quoting. The spindle interior was thoroughly contaminated with coolant sludge which caused failure of the front quad bearing set. In addition, we found that the 100mm housing bore, which appeared to have been previously plated & ground, was worn oversized out of tolerance in both the front & rear. The shaft taper was also worn with slightly more runout than we would find acceptable, and there was some damage at the rear of the shaft where an adjusting spacer is located. Several push-connect oil line fittings were snapped off, and the ID of the drive pulley was severely fretted and had several damaged teeth as well. The gripper (collet) components had light wear but were perfectly usable.
After a grind/plate/grind of the 100mm housing bores and a kiss grind of the shaft wear & damage, we assembled the spindle with new bearings, Bellevilles, oil fittings, o-rings, assembly screws & drive pulley. We ran the spindle up for five hours to distribute the new Kluber bearing grease and to insure that the thermal & vibration characteristics were acceptable. After final trim balance & QC, our customer is once again producing high-precision parts used in the defense of our nation.
Does your spindle need repair? GET A QUOTE TODAY
This customer called saying that their 2 year old spindle is making chatter on the part. They said it sounds ok running with no load but makes noise during a cut. They sent the Doosan Puma spindle to [...]
8,000 rpm 40 Taper Spindle had 25 microns of run out in the taper and was contaminated with coolant causing the bearings to fail. Our evaluation determined that coolant was entering the spin [...]
Daewoo DMV-3016, 8,000 RPM stator drive, oil mist lubrication, CAT40 taper The bearings in this vertical machining center spindle were very noisy when it arrived… [...]
50 Taper The bearings of this spindle were loud during operation. They had reached the end of their life. The taper had 12 microns of run out. We were able to kiss grind the taper to eliminate [...]
Doosan Puma 2500 LSY Spindle Rebuild Our customer sent us this spindle for repair because it had been crashed about a year prior and was making noise. It also developed a “flat spot” that you cou [...]
I really didn’t expect this; You guys really pulled it off! My many thanks to Sandy, Louis and your outstanding crew for helping us get back into production.
Lou all in all everything is running good. Just had a call from Sandy just the other day, its funny great minds think alike. Its great not to be sending spindles out on a regular basis since you addressed my problems, but I know they will still be coming sooner or later. Never a problem when we get them back , run better than new. Hope everything is ok there. Please tell everyone there that we here appreciate everything that you do to keep us up and running and the quick turnarounds. Have delt with the rest now deal with the best. Have a great week end and up and coming holiday.
Thank you Debbie just received spindle today and WOW ! what a nice job. Can’t wait to use it. Thank the Northland team for us for a job well done
Both of the spindles that you repaired are on the machines and running great. We don’t have any spares for those grinders. We probably will not be purchasing a spare, as you have been able to turn around the repairs quickly and the price of a spare is cost prohibitive.
I am writing to thank Northland Tool for going the extra mile and saving my company from expensive machine downtime and expensive repairs. We have always sent our Chiron spindles for repair as a shaft with bearings. None of our previous rebuilders pointed out the bearing fretting or the fact that the housing in the machine was out of tolerance and causing premature failure to the spindles. After Northland fixed the housings the spindles have never sounded as good or run as well! Great job guys!
The detailed cause of failure reports and the expert technical advice that Northland Tool provides is bar none the best I have ever seen. We struggled to keep two of our large our milling spindles running for longer than 6 to 12 months. Northland Tools evaluation showed that the hydraulic nuts were not holding the assembly together causing premature spindle failure. We discussed this in detail and mutually decided to modify the spindle shaft to prevent this from occurring again. The first spindle we performed this on is still in the machine running like new after 3 years. That’s over three times the life of previous repairs and it’s still going strong. Easily over $40,000.00 of savings so far on that one machine and counting.
Your people go above and beyond the call of duty when it comes to spindle repair. When we had difficulty with the spindle installation and we were able to talk directly to a spindle technician that helped us troubleshoot the issue it helped us out of a bind. We have sent several spindles to you and have nothing but great things to say.
Thank you for your attention with my quick turn spindle repair. Your status updates allowed me to plan around machine downtime and I now know that you deliver on your promises. In the past other spindle repair vendors talked a big game and consistently failed to deliver. You not only delivered my spindle before the due date but you kept me informed throughout the entire repair process.
You performed a miracle with my BIG PLUS spindle. After crashing the spindle severely damaging the taper we found that a replacement spindle was not only cost prohibitive but had a long delivery. Your repair was a fraction of the cost of new and you never would know that the spindle was damaged to the extent it was.
Catastrophic bearing failure was the main cause of this spindle malfunction
Continue reading to learn how Northland Tool performed this repair and converted a Weiss GHK 176239 spindle from grease-injected to permanent grease lubrication…