Possible cause of failure:
All bearings are contaminated.
Front and rear shaft journals, shoulder and pilot are not at ISO.
Rear pulley taper area and face are marked up.
Rear shaft nut is loose, the rear bearing spun on the shaft.
Tool and pulley are bent.
Clean, inspect overall dimensions.
Grind, chrome plate and finish grind the journals and pilot.
Kiss grind the shoulders, pulley taper area and face.
Replace bearings, pulley, and bolts.
Adjust preload, balance, assemble and break in. Final quality control inspection.
Does your spindle need repair? GET A QUOTE TODAY
2,600 RPM In most companies there are several operators working on the same machine. In this case the third shift operator took the spindle apart trying to figure out what was happening with th [...]
12,000 RPM The grease was completely washed out of this spindle causing bearing failure. This can be caused by coolant being directed at the face of the spindle or not removing coolant from the [...]
Never to old to be rebuilt. This spindle failed from what else but old age. We reconditioned the worn parts and rebuilt the spindle. With us bringing the tolerances up to date and the advances in bear [...]
35,000 RPM This spindle came with front bearing failure from contamination. The pilot had 22 microns runout and was oversized by 13-23 microns. Rear pulley taper had 60 microns runout. Front an [...]
90,000 RPM ID grinding spindle These spindles were made for Heald by Gamfior in Italy. Special care must be taken during this repair to make sure all tolerances are held. Balance, bearing fits, taper [...]
Heald High Speed Grinding Spindle Rebuild This high speed spindle had a worn ball cage housing. This must be properly measured and held to particular tolerances as it determines the preload of the be [...]
Heald 411 Spindle Repair Heald 411 Spindle Rebuild Economy was the route the customer wanted to take with this repair. They had tried to fix it themselves and realized that it would be better to send [...]
Heald Red Head 411 Spindle Repair and Modification Heald Red Head 411 Spindle Rebuild Possible cause of failure: Drive pulley ears, pulley nut & housing pin are damaged. Customer requested an [...]
Heald Red Head 51-1 Spindle Rebuild We still rebuild the golden oldies too. We upgraded this spindle from oil bath lubrication to greased for life. This allows the spindle to have a higher top s [...]
Heald Red Head 405 Spindle Rebuild Possible cause of failure: All bearings are contaminated. Front and rear shaft journals, shoulder and pilot are not at ISO. Rear pulley taper area and face are m [...]
Possible cause of failure: Spindle was crashed Pilot has 8 microns runout Ball cage is loose with varying ball sizes Repair action: Clean, inspect overall dimensions Replace bearings [...]
I really didn’t expect this; You guys really pulled it off! My many thanks to Sandy, Louis and your outstanding crew for helping us get back into production.
Lou all in all everything is running good. Just had a call from Sandy just the other day, its funny great minds think alike. Its great not to be sending spindles out on a regular basis since you addressed my problems, but I know they will still be coming sooner or later. Never a problem when we get them back , run better than new. Hope everything is ok there. Please tell everyone there that we here appreciate everything that you do to keep us up and running and the quick turnarounds. Have delt with the rest now deal with the best. Have a great week end and up and coming holiday.
Thank you Debbie just received spindle today and WOW ! what a nice job. Can’t wait to use it. Thank the Northland team for us for a job well done
Both of the spindles that you repaired are on the machines and running great. We don’t have any spares for those grinders. We probably will not be purchasing a spare, as you have been able to turn around the repairs quickly and the price of a spare is cost prohibitive.
I am writing to thank Northland Tool for going the extra mile and saving my company from expensive machine downtime and expensive repairs. We have always sent our Chiron spindles for repair as a shaft with bearings. None of our previous rebuilders pointed out the bearing fretting or the fact that the housing in the machine was out of tolerance and causing premature failure to the spindles. After Northland fixed the housings the spindles have never sounded as good or run as well! Great job guys!
The detailed cause of failure reports and the expert technical advice that Northland Tool provides is bar none the best I have ever seen. We struggled to keep two of our large our milling spindles running for longer than 6 to 12 months. Northland Tools evaluation showed that the hydraulic nuts were not holding the assembly together causing premature spindle failure. We discussed this in detail and mutually decided to modify the spindle shaft to prevent this from occurring again. The first spindle we performed this on is still in the machine running like new after 3 years. That’s over three times the life of previous repairs and it’s still going strong. Easily over $40,000.00 of savings so far on that one machine and counting.
Your people go above and beyond the call of duty when it comes to spindle repair. When we had difficulty with the spindle installation and we were able to talk directly to a spindle technician that helped us troubleshoot the issue it helped us out of a bind. We have sent several spindles to you and have nothing but great things to say.
Thank you for your attention with my quick turn spindle repair. Your status updates allowed me to plan around machine downtime and I now know that you deliver on your promises. In the past other spindle repair vendors talked a big game and consistently failed to deliver. You not only delivered my spindle before the due date but you kept me informed throughout the entire repair process.
You performed a miracle with my BIG PLUS spindle. After crashing the spindle severely damaging the taper we found that a replacement spindle was not only cost prohibitive but had a long delivery. Your repair was a fraction of the cost of new and you never would know that the spindle was damaged to the extent it was.
Catastrophic bearing failure was the main cause of this spindle malfunction
Continue reading to learn how Northland Tool performed this repair and converted a Weiss GHK 176239 spindle from grease-injected to permanent grease lubrication…