At Northland Tool and Electronics we component and assembly balance spindles during the repair process. This guarantees you a smooth running spindle that will actually last longer because less stress will be placed on the bearings. During the installation process of this particular Kitamura spindle it is necessary to remove some of the rotating components from the rear of the spindle. We clearly mark their orientation before shipment so there is little possibility of reinstalling them in the wrong orientation.
Possible cause of failure:
Bearing quad set are rough, due to use.
Clean, inspect overall dimensions.
Replace ceramic quad set bearings and high speed roller bearing, orings and screws.
Adjust preload, balance, assemble and break in. Final quality control inspection.
Does your spindle need repair? GET A QUOTE TODAY
10,000 rpm This customer called and needed a spindle repair done within 5 days. We received the spindle and expedited the breakdown process. The rear roller bearing cage had failed causing th [...]
13,000 rpm Oil Mist Lubricated The front bearings failed in this spindle. The taper had run out and the pulley needed to be reworked to function properly. [...]
15,000 rpm 40 taper Front bearings had a catastrophic failure. The drawbar was bent and the taper had run out. We kiss ground the taper, replaced the drawbar and rebuilt the spindle. [...]
10,000 rpm This spindle needed a grind plate grind to the taper and the front bearing housing. After completion of the grinding the spindle was assembled, test run and balanced. [...]
This Kitamura My-Center Spindle has grease lubrication and is belt driven. This particular spindle runs at 10K rpm and in the photos, Spindle Repair Technician, Andy, is breaking down the spindle a [...]
This spindle was pulled by our customer because it started “growling” when it was run. The front bearing was close to failure. This may have been caused by bearing overload or the bearings reached [...]
Possible cause of failure: Front bearing failure from contamination Taper is worn Repair action: Clean, inspect overall dimensions Replace bearings Kiss grind the taper Adjust prel [...]
3,000 rpm A Kitamura machine tool dealer we work closely with was called to pull a spindle from their customer’s machine and found that the cause of the problem was the transmission for the s [...]
Kitamura Spindle Rebuild At Northland Tool and Electronics we component and assembly balance spindles during the repair process. This guarantees you a smooth running spindle that will actually last l [...]
I really didn’t expect this; You guys really pulled it off! My many thanks to Sandy, Louis and your outstanding crew for helping us get back into production.
Lou all in all everything is running good. Just had a call from Sandy just the other day, its funny great minds think alike. Its great not to be sending spindles out on a regular basis since you addressed my problems, but I know they will still be coming sooner or later. Never a problem when we get them back , run better than new. Hope everything is ok there. Please tell everyone there that we here appreciate everything that you do to keep us up and running and the quick turnarounds. Have delt with the rest now deal with the best. Have a great week end and up and coming holiday.
Thank you Debbie just received spindle today and WOW ! what a nice job. Can’t wait to use it. Thank the Northland team for us for a job well done
Both of the spindles that you repaired are on the machines and running great. We don’t have any spares for those grinders. We probably will not be purchasing a spare, as you have been able to turn around the repairs quickly and the price of a spare is cost prohibitive.
I am writing to thank Northland Tool for going the extra mile and saving my company from expensive machine downtime and expensive repairs. We have always sent our Chiron spindles for repair as a shaft with bearings. None of our previous rebuilders pointed out the bearing fretting or the fact that the housing in the machine was out of tolerance and causing premature failure to the spindles. After Northland fixed the housings the spindles have never sounded as good or run as well! Great job guys!
The detailed cause of failure reports and the expert technical advice that Northland Tool provides is bar none the best I have ever seen. We struggled to keep two of our large our milling spindles running for longer than 6 to 12 months. Northland Tools evaluation showed that the hydraulic nuts were not holding the assembly together causing premature spindle failure. We discussed this in detail and mutually decided to modify the spindle shaft to prevent this from occurring again. The first spindle we performed this on is still in the machine running like new after 3 years. That’s over three times the life of previous repairs and it’s still going strong. Easily over $40,000.00 of savings so far on that one machine and counting.
Your people go above and beyond the call of duty when it comes to spindle repair. When we had difficulty with the spindle installation and we were able to talk directly to a spindle technician that helped us troubleshoot the issue it helped us out of a bind. We have sent several spindles to you and have nothing but great things to say.
Thank you for your attention with my quick turn spindle repair. Your status updates allowed me to plan around machine downtime and I now know that you deliver on your promises. In the past other spindle repair vendors talked a big game and consistently failed to deliver. You not only delivered my spindle before the due date but you kept me informed throughout the entire repair process.
You performed a miracle with my BIG PLUS spindle. After crashing the spindle severely damaging the taper we found that a replacement spindle was not only cost prohibitive but had a long delivery. Your repair was a fraction of the cost of new and you never would know that the spindle was damaged to the extent it was.
Catastrophic bearing failure was the main cause of this spindle malfunction
Continue reading to learn how Northland Tool performed this repair and converted a Weiss GHK 176239 spindle from grease-injected to permanent grease lubrication…